Search found 193 matches
- Tue May 09, 2006 12:34 am
- Forum: MegaSquirt Fuel Injection
- Topic: My MS doesn't see RPM's on step 56
- Replies: 10
- Views: 8302
My MS doesn't see RPM's on step 56
Yesterday I made the test on step 56 and saw on the Realtime Display that it all went right but the RPM's. It read zero RPMs all the time, although I twisted both RPM knobs for a while. The only modifications I'd already done at this point are: STEP 47: Installed a 1K5 resistor STEP 48: Installed a ...
- Fri May 05, 2006 5:28 am
- Forum: MegaSquirt Fuel Injection
- Topic: MS-EDIS recipe
- Replies: 20
- Views: 16658
- Fri May 05, 2006 12:31 am
- Forum: Gearbox, Clutch and Driveshaft
- Topic: Speedo on GTV6
- Replies: 38
- Views: 30647
I'm still with the GTV6's speedo and the Milano's sender combination problem. I tested my speedo yesterday at the laboratory with an oscilloscope and a signal generator. I fed the speedo with 12V DC and a sinoidal signal with 12V (peak-to-peak) and trying different frequencies, I got the following r...
- Fri May 05, 2006 12:11 am
- Forum: MegaSquirt Fuel Injection
- Topic: MS-EDIS recipe
- Replies: 20
- Views: 16658
- Thu May 04, 2006 5:52 am
- Forum: MegaSquirt Fuel Injection
- Topic: MS-EDIS recipe
- Replies: 20
- Views: 16658
- Thu May 04, 2006 1:23 am
- Forum: MegaSquirt Fuel Injection
- Topic: MS-EDIS recipe
- Replies: 20
- Views: 16658
- Wed May 03, 2006 3:47 am
- Forum: MegaSquirt Fuel Injection
- Topic: MS-EDIS recipe
- Replies: 20
- Views: 16658
MS-EDIS recipe
Ok, guys, I know there are a lot of posts about using MS and EDIS to control ignition, but it's a mess for me. Let's start from the beginning. When you're running your MS and want to control the ignition, then you get an EDIS-6 module and...don't know much. One thing. On an L-jetronic->MS conversion...
- Wed May 03, 2006 3:39 am
- Forum: MegaSquirt Fuel Injection
- Topic: Modifications required on L-Jet=>MS conversion
- Replies: 5
- Views: 5825
- Tue May 02, 2006 9:19 am
- Forum: MegaSquirt Fuel Injection
- Topic: Modifications required on L-Jet=>MS conversion
- Replies: 5
- Views: 5825
- Tue May 02, 2006 2:37 am
- Forum: MegaSquirt Fuel Injection
- Topic: Modifications required on L-Jet=>MS conversion
- Replies: 5
- Views: 5825
- Tue May 02, 2006 1:39 am
- Forum: MegaSquirt Fuel Injection
- Topic: Modifications required on L-Jet=>MS conversion
- Replies: 5
- Views: 5825
Modifications required on L-Jet=>MS conversion
Hi all, I've read that some modifications are required to install the MS I V2.2 on my L-Jet GTV6. I've been told that I must do the following: 1. Substitute R10 and install a 1K6 ohm resistor instead. 2. Substitute the 1N4001 diode and install a 1N4004 instead. 3. Substitute C12 (0.001 uF) for a 0.0...
- Tue May 02, 2006 1:10 am
- Forum: Engine
- Topic: 3.0L 12V rebuild and GTV6 conversion
- Replies: 41
- Views: 34442
- Tue May 02, 2006 1:05 am
- Forum: Performance
- Topic: About injectors...
- Replies: 22
- Views: 16648
- Wed Apr 26, 2006 4:36 am
- Forum: Engine
- Topic: Seb´s GTV6 3.0QV conversion.
- Replies: 191
- Views: 148483
- Wed Apr 26, 2006 1:26 am
- Forum: Performance
- Topic: 3.0 conversion
- Replies: 11
- Views: 8520